Quick Answer: What Is A Drip Edge Used For?

Should you use drip edge touch fascia?

The drip edge should be installed over a piece of 1×2 furring strip so that it stands off from the fascia or rafter tails.

If the drip edge is laid right up against the fascia or rafters, then because of surface tension, the water runs right up against the fascia and underneath the soffit..

What color drip edge should I use?

If your home’s trim and fascia are white, it is recommended you select a white drip edge for seamless blending of elements throughout. If your home has more pops of brown, similar to the home displayed in the photo to the right, you may want to choose a brown drip edge.

What is the difference between drip edge and rake edge?

Drip edge and rake edge are the first parts of the roof system to be installed. … They form a long, narrow piece of metal, which is installed along the perimeter your Roof Deck. Drip edge goes along your eaves trough areas and rake edge goes along your gable ends.

Can you put drip edge on after shingles?

The drip edge is often replaced when new shingles are installed, but it can be replaced at any time. Asphalt roof shingles can become brittle in cold weather, so wait until a warm (but not hot) day to remove and replace eave stripping.

Can drip edge be installed after gutters?

The outer edge should extend over the gutter. If for some reason it doesn’t, you can pull the edge out slightly from under the shingles.

Why is water dripping between gutter and fascia?

Water Gets Behind the Gutter If water is dripping behind your gutter, it’s probably because it was installed without any flashing over the back of the gutter. The gutter apron will prevent the dripping. A gutter apron is a bent piece of flashing that tucks up under the shingles and over the gutter.

Do you need to replace drip edge when replacing roof?

Drip Edge Flashing Drip edge comes in 10-foot strips and attaches to the roof deck before the roofing felt goes on. Unless the old drip edge is in like-new condition, replace it.

Is a drip edge necessary on a metal roof?

A: A drip edge is not always required by local building codes, but installing a drip edge is a good idea—especially if the home is in an area that experiences a lot of wind-driven rain. This applies whether you are working with asphalt or metal because a drip edge allows water to fall away from the fascia.

How important is drip edge?

A drip edge is a piece of roofing trim. The drip edge supports overhanging shingles at the ends of a roof, providing structure to the overhang and directing water to the gutters and away from the fascia of the roof. Drip edges also help prevent shingles at the end of a roof from cracking, sagging, and becoming limp.

How far should drip edge be from fascia?

2 inchesCode requires that the drip edge extend at least 2 inches onto the roof from the fascia board. This drip edge extends much farther. Nailing along the eaves should be spaced at no more than 12 inches on-center.

Does drip edge go on before fascia?

Drip edge flashing directs roof runoff away from the roof fascia and edge and into gutters or at least not down the fascia board (if no gutters are installed) and it is recommended by roofing standards, manufacturers, and experts.

How much should shingles overhang drip edge?

Asphalt shingles should overhang the exterior edge of the drip edge by ¼ to ¾-inch. Check local building code for drip edge requirements prior to the start of your roofing project.

How much does drip edge cost?

Drip Edges: $1-$2 per linear foot installed. Inspect and replace drip edges as necessary. Drip edges are added to the roof to direct water into the gutters. Other Damage – Have a professional inspect your eaves for damage before repairing fascia and soffits.

Can drip edge be painted?

Yes you can paint the aluminum drip edge and it hold up very well. Just be sure it is clean and paint it with a good exterior acrylic primer and finish with a exterior acrylic semi-gloss house paint.

Are drip edges necessary?

Without a drip edge, water may end up beneath the shingles and may cause damage to various parts of the home. Though your home may not have originally had a drip edge installed, drip edges are now required by most building codes across North America to protect homes from damage.

Do gutters go under or over drip edge?

If the overlap is too short, fix it by placing drip edge under the first row of roof shingles and be sure that the exterior edge is reaching over the gutter. If the gutter is lower than the bottom edge of the drip edge, install flashing behind the drip edge and over the back edge of the gutter to remove the gap.